Microdermabrasion Machine 3 in 1 Skin Grinding Spray Hydrating Professional Dermabrasion Machine AU

Coolbe: Informace o výrobku poskytuje prodejce. Bez ohledu na uvedené informace nemá výrobek žádné preventivní, diagnostické, léčebné ani rehabilitační vlastnosti, není to lék a neměl by být používán k jakýmkoli léčebným účelům. Před použitím se poraďte s lékařem.

-----

Feature: 1. QUALITY MATERIAL: Made of quality material, durable, no irritation, no contamination, uncomfortable when using, easy to use and comfortable, suitable for all skin types. 2. HIGH PRESSURE SPRAY: The high pressure spray bottle compresses the moisture and nutrients in the lotion into tiny molecules and infuses the skin to achieve the purpose of deep moisturizing and nourishing. 3. GRINDING HEAD: The grinding head adopts crystalstone specially processed for the problem skin, and uses vacuum suction to remove the necrotic cells on the skin, and remove the deep oil and dirt. Clean pores. 4. BLACK HEAD SUCTION: The product uses black head suction set, using more than 60KPA suction, will be located in the deep skin dirt, end insect black head, white head clean, and open clogged pores. 5. CRYSTALSTONE SKIN CLEANSER: Professional machine provides a comfortable skin outside repair procedure by using sterile crystalstone to remove skin. Specification: Item Type: Microdermabrasion machine Material: ABS Operational order Please connect all accessories to the machine first. 1. Unscrew the vacuum connector and make sure there is a large cotton filter in the center and a large black round around the connector head. 2. Check and tighten the connector. Then connect the PVC hose to the connector. 3. Insert the other end of the PVC hose into the other end of the glue stick. 4. Place a small cotton filter on the end of your wand. (there is a small black round around the head) (3) Slowly adjust the vacuum power, from minimum to maximum, the vacuum gauge will display pressure data. In general, do not set the power to maximum unless necessary. (4) Frequency of treatment. (see paper manual) (5) Place the diamondstone on the outside of the skin(starting from the forehead) and slide it slowly. Do not let the tip of a diamondstone sit in one place for too long as this can cause skin damage. (6) Gently stretch the skin with thumb and other fingers, and slide the finger plate in treatment area 2 to 3 times. Then through in different directions to prevent streaking lines. The stroke or polish action can be used in different locations. (7) After treatment, use a soft brush to remove all remaining dead skin and rinse with a wet sponge or cool towel. (8) Let your skin dry, then apply any skin products you need. (9) When cleaning diamondstones, use a toothbrush or a cotton swab dipped in a small amount of alcohol to wipe off the dirty impurities, and then use ultraviolet lamp or high temperature disinfection. Vacuum function 1. Connect the black hose to the vacuum connector (OUTPUT), and connect the plastic vent pipe to the other end. 2. Adjust the vacuum strength knob for the suction you want. 3. Press stomata with finger to increase suction. The spray function 1. Connect the red hose to the spray connector and the other end to the spray bottle. 2. Press the bottle lid with your finger to atomize the toner. 3. Spray from customer forehead. Keep the client eyes and mouth closed to prevent fluid from entering the client " s nose. Keep the bottle away from your face. 4. Spout should be clean. Do not spray toner with impurities or sediment. 5. Turn off the power after use.. Package List: 1 x Host 1 x Red Hose1 x White Hose1 x Black Hose3 x Miniature Handle9 x Diamondstone Head4 x Black Silica Gel Circle2 x Transparent Silica Gel Circle1 x Pack of Cotton Sheet1 x Power Line2 x Steam Bottle 3 x Plastic Suction Nozzle1 x Instruction 1 x Bracket1 x Screwdriver1 x Filter Note: 1. Clean the nursing area before use, so as not to affect the effect. 2. When adjusting the strength, test it in the hand or arm first. 3. When operating, the correct way is to keep sliding or rotating the leather head. 4. The polishing head of microcarving should be kept clean and clean. Gently wipe it with cotton when disinfecting or cleaning, and do not fall and strike. 5. Alcohol can not be used directly after disinfection. Alcohol is a volatile liquid. 6. The head should not stay at the same point of the skin for too long, pay attention to stay more than 15 seconds, because of high pressure will lead to redness or bleeding.